New Products

Brand: HDBUDDY Model: HDBUDDY Terrestrial High Definition Freeview Accredited MHEG-5 Middleware Freeview EPG Easy Installation Will find new channels when they become available Follows Freeview assigned channel numbers Freeview 8 day Electronic Programme Guide High Definition via HDMI output. HDMI 1.3 supports up to 1080p Software upgrades via OTA and USB Low power consumption mode. Requires a UHF Antenna INPUTS & OUTPUTS Antenna In, Antenna Out,HDMI, Component Out, USB (Software upgrade only) Audio L+R, S/PDIF, SCART Accessories Remote Control, Batteries, HDMI CABLE User Manual

Brand: HDBUDDY Model: HDBUDDY Terrestrial High Definition Freeview Accredited MHEG-5 Middleware Freeview EPG Easy Installation Will find new channels when they become available Follows Freeview assigned channel numbers Freeview 8 day Electronic Programme Guide High Definition via HDMI output. HDMI 1.3 supports up to 1080p Software upgrades via OTA and USB Low power consumption mode. Requires a UHF Antenna INPUTS & OUTPUTS Antenna In, Antenna Out,HDMI, Component Out, USB (Software upgrade only) Audio L+R, S/PDIF, SCART Accessories Remote Control, Batteries, HDMI CABLE User Manual

Brand: HDBUDDY Model: HDBUDDY Terrestrial High Definition Freeview Accredited MHEG-5 Middleware Freeview EPG Easy Installation Will find new channels when they become available Follows Freeview assigned channel numbers Freeview 8 day Electronic Programme Guide High Definition via HDMI output. HDMI 1.3 supports up to 1080p Software upgrades via OTA and USB Low power consumption mode. Requires a UHF Antenna INPUTS & OUTPUTS Antenna In, Antenna Out,HDMI, Component Out, USB (Software upgrade only) Audio L+R, S/PDIF, SCART Accessories Remote Control, Batteries, HDMI CABLE User Manual

Engel Satellite/Terrestrial Diplexer

Engel Satellite/Terrestrial Diplexer

Engel Satellite/Terrestrial Diplexer

Engel 2-way Signal Splitter Can be used to split satellite of terrestrial signal. One in, Two out. All ports have power pass.

Engel 2-way Signal Splitter Can be used to split satellite of terrestrial signal. One in, Two out. All ports have power pass.

Engel 2-way Signal Splitter Can be used to split satellite of terrestrial signal. One in, Two out. All ports have power pass.

Engel 4-way Signal Splitter Can be used to split satellite of terrestrial signal. All ports have power pass.

Engel 4-way Signal Splitter Can be used to split satellite of terrestrial signal. All ports have power pass.

Engel 4-way Signal Splitter Can be used to split satellite of terrestrial signal. All ports have power pass.

50cm satellite dish

50cm satellite dish

50cm satellite dish

Engel Satellite Finder Model: ME7712 Used to align satellite dish. Connect between satellite receiver and satellite dish. Comes with a short connection cable to allow in-line insertion.

Engel Satellite Finder Model: ME7712 Used to align satellite dish. Connect between satellite receiver and satellite dish. Comes with a short connection cable to allow in-line insertion.

Engel Satellite Finder Model: ME7712 Used to align satellite dish. Connect between satellite receiver and satellite dish. Comes with a short connection cable to allow in-line insertion.

KAON KSF-620R2 Multiroom Satellite TV Receiver - Watch different channels in two rooms with one set top box !! - Supports Freeview New Zealand programming and channel numbers - Automatically finds new channel without scanning - Max 3000 channels, Sensitive Tuner - OSD Teletext, VBI Teletext and Subtitling function - Fast Auto-programming and User-friendly installation - Fast Auto-programming and User-friendly installation - Powerful channel control by Favourites, Lock and Skip - Channel sorting by CAS, Lock, Name, Satellite and Network - Variable Aspect Ratio with 4:3, Letter-Box, Full Screen and 16:9 QUESTIONS & ANSWERS What is Multiroom? Multiroom allows watching of more than one different channel in your home. The KSF-620R2 allows you to watch two different channels in your home through one physical unit. What is Dynamic Update? With dynamic update, the receiver will automatically detect changes in transmission of services and updates itself without the need to scan. In simple terms, the receiver will update any changes to channel offerings by itself without the need to do a manual scan. How can you watch Multiroom? The Multiroom receiver behaves like two set top boxes but is physically only one. It has two tuners, two sets of memory and processors on its main board allowing it to operate like two receivers. It has two outputs which can be used to view two different channels. Within the Multiroom, we call the two receivers Master & Slave. Can I change a channel without affecting the other channel? Yes, you can. The slave receiver allows remote control function via the RF cable. This allows changing of the channels from a remote location. What are the most common uses of this receiver? a) Installation in your main lounge and bedroom. b) Watching one channel and recording another ( via your analog recorder, VCR etc ) c) MATV Headends. Allows reduction of number of receivers in headends. How do you suggest I connect the receiver to my equipment? a) From the Master receiver, connect to your main TV via RCA/AV ( or any of the SCART output ). b) From the Slave receiver, connect to your second TV via the RF cable c) Connect the RCA/AV out of the Slave receiver to your VCR d) If your VCR has more than one Input, you can connect one of the outputs from the Master receiver as well. I want to watch picture from both Master and Slave in my second room. Is this possible? Yes, this is possible. Do the following: a) Loop your Antenna out of the Master receiver to Antenna In of Slave receiver. b) Go into the setup of the Master receiver and change the RF Output channel to UHF 51 or any other free one. c) Start the tuning on your second TV and stop once you find the picture from the Master. d) Save to any of the free channel numbers available on your TV and then exit on your TV. I have more than two TVs in the house, can I control the slave receiver from more than two rooms? Yes, you can. You can install an all powerpass splitter and RF cabling to your other rooms from your RF output of the slave receiver. You can then install additional room kits which will allow you to watch the picture from the slave receiver and allow you to change the channel. I use this receiver to watch one channel and record another. How do I change the channel on the slave receiver without going to the second room to change the channel? In the main room, press the PAUSE button on the remote control for about two seconds and then release. The receiver will switch to the Slave and the front panel will display "slave". Now you can change the channels and also set up the second. Note: This function is only available from software release 13.05.05. I can no longer see the picture on the second tuner. It was working before. What could be the problem? It is possible that the second tuner is on standby. Press the standby button on the remote control from the second room. Allow about 30 seconds for the receiver to start up.

KAON KSF-620R2 Multiroom Satellite TV Receiver - Watch different channels in two rooms with one set top box !! - Supports Freeview New Zealand programming and channel numbers - Automatically finds new channel without scanning - Max 3000 channels, Sensitive Tuner - OSD Teletext, VBI Teletext and Subtitling function - Fast Auto-programming and User-friendly installation - Fast Auto-programming and User-friendly installation - Powerful channel control by Favourites, Lock and Skip - Channel sorting by CAS, Lock, Name, Satellite and Network - Variable Aspect Ratio with 4:3, Letter-Box, Full Screen and 16:9 QUESTIONS & ANSWERS What is Multiroom? Multiroom allows watching of more than one different channel in your home. The KSF-620R2 allows you to watch two different channels in your home through one physical unit. What is Dynamic Update? With dynamic update, the receiver will automatically detect changes in transmission of services and updates itself without the need to scan. In simple terms, the receiver will update any changes to channel offerings by itself without the need to do a manual scan. How can you watch Multiroom? The Multiroom receiver behaves like two set top boxes but is physically only one. It has two tuners, two sets of memory and processors on its main board allowing it to operate like two receivers. It has two outputs which can be used to view two different channels. Within the Multiroom, we call the two receivers Master & Slave. Can I change a channel without affecting the other channel? Yes, you can. The slave receiver allows remote control function via the RF cable. This allows changing of the channels from a remote location. What are the most common uses of this receiver? a) Installation in your main lounge and bedroom. b) Watching one channel and recording another ( via your analog recorder, VCR etc ) c) MATV Headends. Allows reduction of number of receivers in headends. How do you suggest I connect the receiver to my equipment? a) From the Master receiver, connect to your main TV via RCA/AV ( or any of the SCART output ). b) From the Slave receiver, connect to your second TV via the RF cable c) Connect the RCA/AV out of the Slave receiver to your VCR d) If your VCR has more than one Input, you can connect one of the outputs from the Master receiver as well. I want to watch picture from both Master and Slave in my second room. Is this possible? Yes, this is possible. Do the following: a) Loop your Antenna out of the Master receiver to Antenna In of Slave receiver. b) Go into the setup of the Master receiver and change the RF Output channel to UHF 51 or any other free one. c) Start the tuning on your second TV and stop once you find the picture from the Master. d) Save to any of the free channel numbers available on your TV and then exit on your TV. I have more than two TVs in the house, can I control the slave receiver from more than two rooms? Yes, you can. You can install an all powerpass splitter and RF cabling to your other rooms from your RF output of the slave receiver. You can then install additional room kits which will allow you to watch the picture from the slave receiver and allow you to change the channel. I use this receiver to watch one channel and record another. How do I change the channel on the slave receiver without going to the second room to change the channel? In the main room, press the PAUSE button on the remote control for about two seconds and then release. The receiver will switch to the Slave and the front panel will display "slave". Now you can change the channels and also set up the second. Note: This function is only available from software release 13.05.05. I can no longer see the picture on the second tuner. It was working before. What could be the problem? It is possible that the second tuner is on standby. Press the standby button on the remote control from the second room. Allow about 30 seconds for the receiver to start up.

KAON KSF-620R2 Multiroom Satellite TV Receiver - Watch different channels in two rooms with one set top box !! - Supports Freeview New Zealand programming and channel numbers - Automatically finds new channel without scanning - Max 3000 channels, Sensitive Tuner - OSD Teletext, VBI Teletext and Subtitling function - Fast Auto-programming and User-friendly installation - Fast Auto-programming and User-friendly installation - Powerful channel control by Favourites, Lock and Skip - Channel sorting by CAS, Lock, Name, Satellite and Network - Variable Aspect Ratio with 4:3, Letter-Box, Full Screen and 16:9 QUESTIONS & ANSWERS What is Multiroom? Multiroom allows watching of more than one different channel in your home. The KSF-620R2 allows you to watch two different channels in your home through one physical unit. What is Dynamic Update? With dynamic update, the receiver will automatically detect changes in transmission of services and updates itself without the need to scan. In simple terms, the receiver will update any changes to channel offerings by itself without the need to do a manual scan. How can you watch Multiroom? The Multiroom receiver behaves like two set top boxes but is physically only one. It has two tuners, two sets of memory and processors on its main board allowing it to operate like two receivers. It has two outputs which can be used to view two different channels. Within the Multiroom, we call the two receivers Master & Slave. Can I change a channel without affecting the other channel? Yes, you can. The slave receiver allows remote control function via the RF cable. This allows changing of the channels from a remote location. What are the most common uses of this receiver? a) Installation in your main lounge and bedroom. b) Watching one channel and recording another ( via your analog recorder, VCR etc ) c) MATV Headends. Allows reduction of number of receivers in headends. How do you suggest I connect the receiver to my equipment? a) From the Master receiver, connect to your main TV via RCA/AV ( or any of the SCART output ). b) From the Slave receiver, connect to your second TV via the RF cable c) Connect the RCA/AV out of the Slave receiver to your VCR d) If your VCR has more than one Input, you can connect one of the outputs from the Master receiver as well. I want to watch picture from both Master and Slave in my second room. Is this possible? Yes, this is possible. Do the following: a) Loop your Antenna out of the Master receiver to Antenna In of Slave receiver. b) Go into the setup of the Master receiver and change the RF Output channel to UHF 51 or any other free one. c) Start the tuning on your second TV and stop once you find the picture from the Master. d) Save to any of the free channel numbers available on your TV and then exit on your TV. I have more than two TVs in the house, can I control the slave receiver from more than two rooms? Yes, you can. You can install an all powerpass splitter and RF cabling to your other rooms from your RF output of the slave receiver. You can then install additional room kits which will allow you to watch the picture from the slave receiver and allow you to change the channel. I use this receiver to watch one channel and record another. How do I change the channel on the slave receiver without going to the second room to change the channel? In the main room, press the PAUSE button on the remote control for about two seconds and then release. The receiver will switch to the Slave and the front panel will display "slave". Now you can change the channels and also set up the second. Note: This function is only available from software release 13.05.05. I can no longer see the picture on the second tuner. It was working before. What could be the problem? It is possible that the second tuner is on standby. Press the standby button on the remote control from the second room. Allow about 30 seconds for the receiver to start up.

Engel CA1700 Digital TV coaxial Cable Model: CA1700 Coaxial cable for reception of Digital TV.

Engel CA1700 Digital TV coaxial Cable Model: CA1700 Coaxial cable for reception of Digital TV.

Engel CA1700 Digital TV coaxial Cable Model: CA1700 Coaxial cable for reception of Digital TV.

Engel Twin User LNB Model: AN7106 This LNB allows access for two receivers to one satellite simultaneously. Typical use is when access to both vertical and horizontal polarity signals are required simultaneously. Also, suitable for TVHeadend. Universal LNB settings. Local Oscillator Frequency: 950 MHz for Low Sat Band. Local Oscillator Frequency: 10600 MHz for Hight Sat Band. 22KHz Tone for switching between between Low and High Sat Band. Can be used with normal Freeview receiver with LO setting of 10600 and 22KHz ON.

Engel Twin User LNB Model: AN7106 This LNB allows access for two receivers to one satellite simultaneously. Typical use is when access to both vertical and horizontal polarity signals are required simultaneously. Also, suitable for TVHeadend. Universal LNB settings. Local Oscillator Frequency: 950 MHz for Low Sat Band. Local Oscillator Frequency: 10600 MHz for Hight Sat Band. 22KHz Tone for switching between between Low and High Sat Band. Can be used with normal Freeview receiver with LO setting of 10600 and 22KHz ON.

Engel Twin User LNB Model: AN7106 This LNB allows access for two receivers to one satellite simultaneously. Typical use is when access to both vertical and horizontal polarity signals are required simultaneously. Also, suitable for TVHeadend. Universal LNB settings. Local Oscillator Frequency: 950 MHz for Low Sat Band. Local Oscillator Frequency: 10600 MHz for Hight Sat Band. 22KHz Tone for switching between between Low and High Sat Band. Can be used with normal Freeview receiver with LO setting of 10600 and 22KHz ON.

IF Line Amplifier Model: AM7530 Signal amplifier. Improves strength of the signal. Typically installed between your satellite dish and satellite receiver.

IF Line Amplifier Model: AM7530 Signal amplifier. Improves strength of the signal. Typically installed between your satellite dish and satellite receiver.

IF Line Amplifier Model: AM7530 Signal amplifier. Improves strength of the signal. Typically installed between your satellite dish and satellite receiver.